有人說:一般變壓器、電感和漏感測試的頻率選1K/1V;
也有人說:一般變壓器、電感和漏感測試的頻率選100khz,0.1v．原因是用1v時,場強太強;
還有人說:根據產品工作時候的頻率來測試,比如說工作在50K,那麼測試的頻率選50K/1V;
我想針對這個問題探討下,,希望能夠解決!
探討一般變壓器、電感和漏感的測試條件(關注中)
全部回復(18)
正序查看
倒序查看
此問題真是問得太好了.我以前也問過一個前輩,據他說大部份的測試頻率是依美軍規所訂:其測試頻率應與使用頻率相近才可(只是聽說,但一直沒有機會證實).
現在的廠商于實際生產中感值一般都依1KHz漏感以50KHz居多.至于為何這樣,我也沒打聽到.其中我只了解到Inverter transformer的漏感依50KHz是因?yàn)镮nverter transformer的工作頻率在50KHz左右.
關注此帖中.請各位多多指教.
現在的廠商于實際生產中感值一般都依1KHz漏感以50KHz居多.至于為何這樣,我也沒打聽到.其中我只了解到Inverter transformer的漏感依50KHz是因?yàn)镮nverter transformer的工作頻率在50KHz左右.
關注此帖中.請各位多多指教.
0
回復
@steven.lee
此問題真是問得太好了.我以前也問過一個前輩,據他說大部份的測試頻率是依美軍規所訂:其測試頻率應與使用頻率相近才可(只是聽說,但一直沒有機會證實). 現在的廠商于實際生產中感值一般都依1KHz漏感以50KHz居多.至于為何這樣,我也沒打聽到.其中我只了解到Invertertransformer的漏感依50KHz是因?yàn)镮nvertertransformer的工作頻率在50KHz左右. 關注此帖中.請各位多多指教.
過年好!
STEVEN兄說的對.
測試條件當然要和工作條件越接近越好.
一般來說,小功率高頻變壓器電感值測試條件多為1KHZ 1V.
這個應該和板子工作頻率很接近吧.
我司為專業生產電子變壓器的廠家,我也有問過客戶變壓器工程師,說的是以上的答案.
希望對大家有幫助!
王先生 13562187623
STEVEN兄說的對.
測試條件當然要和工作條件越接近越好.
一般來說,小功率高頻變壓器電感值測試條件多為1KHZ 1V.
這個應該和板子工作頻率很接近吧.
我司為專業生產電子變壓器的廠家,我也有問過客戶變壓器工程師,說的是以上的答案.
希望對大家有幫助!
王先生 13562187623
0
回復
@tkwz2000
先謝謝!但我還是直接點說,我認為弄得不夠清楚,我還想知道,具體是依照什么標準?選擇一個測試條件,總該有它的原因,我認為是這樣的.
這1KHz/1V的標準應該是有幾十年歷史了吧,國家級的校正實驗室里的標準電感也是用這標準測量厘定的,這可能與當時的應用和測量技術有關吧.另外如果Q值太低的話,測量結果誤差比較大,所以小電感時要采用較高頻率.
0
回復
@steven.lee
此問題真是問得太好了.我以前也問過一個前輩,據他說大部份的測試頻率是依美軍規所訂:其測試頻率應與使用頻率相近才可(只是聽說,但一直沒有機會證實). 現在的廠商于實際生產中感值一般都依1KHz漏感以50KHz居多.至于為何這樣,我也沒打聽到.其中我只了解到Invertertransformer的漏感依50KHz是因?yàn)镮nvertertransformer的工作頻率在50KHz左右. 關注此帖中.請各位多多指教.
能否告訴我具體標準
0
回復
看看這段話可能有一些啟發．
Inductance is measured on a bridge with variable voltage and frequency.The flux density should be
less than 10 gauss.Cores have to be properly mounted around the measuring coil,or for toroids,
wound with the correct number of turns.
Testing at low gauss level is important.Magnetic material characteristics change considerably at higher
drive levels.Since all applications are different,it is necessary for manufacturers to normalize
characteristics at a low level to insure a degree of consistency in magnetic properties and that “apples
are compared to apples.”
Inductance is measured on a bridge with variable voltage and frequency.The flux density should be
less than 10 gauss.Cores have to be properly mounted around the measuring coil,or for toroids,
wound with the correct number of turns.
Testing at low gauss level is important.Magnetic material characteristics change considerably at higher
drive levels.Since all applications are different,it is necessary for manufacturers to normalize
characteristics at a low level to insure a degree of consistency in magnetic properties and that “apples
are compared to apples.”
0
回復
@bean
看看這段話可能有一些啟發．Inductanceismeasuredonabridgewithvariablevoltageandfrequency.Thefluxdensityshouldbelessthan10gauss.Coreshavetobeproperlymountedaroundthemeasuringcoil,orfortoroids,woundwiththecorrectnumberofturns.Testingatlowgausslevelisimportant.Magneticmaterialcharacteristicschangeconsiderablyathigherdrivelevels.Sinceallapplicationsaredifferent,itisnecessaryformanufacturerstonormalizecharacteristicsatalowleveltoinsureadegreeofconsistencyinmagneticpropertiesandthat“applesarecomparedtoapples.”
路過關注
0
回復
