你先說說看.
.

拋磚
我是剛剛接觸開關電源,關于PFC技術,想向各位大蝦學一兩手,雪大俠叫我先說幾句,我就班門弄斧侃幾句,不過我?guī)е摽鴣?lái)的,各位有板磚只管砸.
AC/DC電路對電網的危害及提高功率因數的意義很多書上都有,我就不多說了.
說幾點我的思路
從根本上說PFC是要開關電源的輸入電流與輸入電壓同頻同相.可否這樣:
1．釜底抽薪
對整流電路而言,是要得到一個較為平直的直流電壓供后級開關電路用.也正因?yàn)槿绱瞬旁斐闪藢?duì)電網的污染,去掉濾波電容,也就沒污染的問題.設計應用脈動直流的開關電路,從根本上解決問題.
2．隨波逐流
   逐流技術在電子鎮流器上應用很多.可否改進后應用于開關電源電路.
3．李代桃僵
   有源功率因數校正技術具有輸入電壓寬,輸出電壓恒定,干脆解決隔離問題就用有源功率因數校正電路做降壓電路.
4．以一當十
   單級PFC技術對泵電源電路進行深入研究

請教一個問題
請教一個問題
我在做一款pfc時,低壓PF值0.98左右.高壓時PF值就掉了很多,0.7,0.8左右.
電流模式為臨界連續模式,pfc IC L6561.請問該從哪些地方入手?

高壓會下降我也遇到過這中情況
只是我們?cè)跍y(cè)試時,是在額定的電壓下測試的

PFC
What bulk voltage you set? I didn\'t meet your question, just now, I design a 240W power used L6561, and what is the feedback compensation value?

two stage
pfc+flyback(100W)
two indepdent control ic.
bulk voltage is about 400Volts.
when load 2.5A, the value of PF is 0.98(110Vac)
but load at 4A,pf drops to 0.88.
can you explain it?

PFC problem
Did you check the bulk voltage and the waveform current sense? I thought the current waveform maybe be distorted, and you need to checvk the input cap of EMI filter after bridge diode (mylar cap), if it is too smaller, will cause this problem, it should be enough. and you need to check Multiplier Characteristics, you can get these information from the application note.

EMI Filter cause PF drops
At high line input, the reactive current through EMI filter will be relatively higher than low line input. So, the PF drops at high line.

CONDUCTION ANGEL and slope compensation
這兩個概念是怎么回事?請大牛解釋下

An other reason
If u use the capacitor in parallel with the PFC rectifier, or the Trr is very large, will also cause the same problem.

檢查Isence電阻是否太小,對高壓時電流信號不足
檢查Isence電阻是否太小,對高壓時電流信號不足

264V輸入PF到0.7X就不正常了
我一般在264V時候都由0.91以上,低電壓時都是1~

你看看前面的派形濾波電容是不是太大了

要不就是你本身PFC電路的問題了

幾點看法
另外,L6561 誤差放大器反饋網絡是否有足夠的帶寬,在寬范圍電壓輸入的時候,更確切的說在HIGH LINE的時候誤差放大器是否工作的線性范圍內.

PFC的MOS RDSON是否太大,整流二極管導通壓降是否太大,以至于在LINE電壓過0時PFC德儲能電感沒有足夠的能量,使得此時PF值下降.

反饋
你調整一下1,2腳之間反饋補償電容的值,稍微調大一些.另外zcd反饋繞組給ic的信號串有一個電阻,試著調整一下這個阻值也會有幫助.

我覺得逐流法用在反擊電路里應該是個好方法.不知為什么沒人用
.

逐流電路的本質是串聯輸入并聯輸出
在改變輸入電流波形的同時,輸出電壓變化很大,對功率較大電路可能不適合,反激電路常用電荷泵式PFC

是的,我也正調此電路,電壓89----200V之間,HP為0.999,電壓升到208時HP變?yōu)?.68,但總功率沒有多大變化,不知調何處???請樓主回復一下吧!!!